{"id":10696,"date":"2026-11-20T06:30:13","date_gmt":"2026-11-20T06:30:13","guid":{"rendered":"https:\/\/www.jinyupaint.com\/?p=10696"},"modified":"2026-11-20T06:30:15","modified_gmt":"2026-11-20T06:30:15","slug":"urethane-cement-specification-table","status":"publish","type":"post","link":"https:\/\/www.jinyupaint.com\/it\/urethane-cement-specification-table.html","title":{"rendered":"Urethane Cement Specifications: System, Load and Chemistry"},"content":{"rendered":"<p class=\"wp-block-paragraph\">A workable set of urethane cement specifications fits on one page. Each row pairs a system with a thickness band, a load class and a chemical class, then states the design life and the test that proves the floor was built to it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That structure answers the four decisions a buyer actually has to make: what goes down, how thick it is, what it must survive, and how anyone will know afterwards. The sections below explain each column, show how to read it against real traffic, and give the wording that holds up in a tender. They also cover the mistakes that appear most often when a table is copied from one project to another.<\/p>\n\n\n\n<h2 id=\"what-a-urethane-cement-specifications-table-should-contain\" class=\"wp-block-heading\">What a urethane cement specifications table should contain<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Six columns carry the whole decision. Remove any one of them and the document stops being a specification and becomes a product list.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>System.<\/strong> The build-up in words: primer, body coat, seal coat, broadcast, cove.<\/li>\n\n\n\n<li><strong><a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-thickness.html\/\" target=\"_blank\" rel=\"noopener\">Thickness band<\/a>.<\/strong> A range rather than a single number, because site-measured thickness always varies.<\/li>\n\n\n\n<li><strong>Load class.<\/strong> The traffic and point loads the row is written for.<\/li>\n\n\n\n<li><strong><a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-chemical-resistance.html\/\" target=\"_blank\" rel=\"noopener\">Chemical class<\/a>.<\/strong> The concentration and temperature the row resists.<\/li>\n\n\n\n<li><strong>Design life.<\/strong> The period the row is expected to serve under the stated cleaning and traffic.<\/li>\n\n\n\n<li><strong>Verification.<\/strong> The test, its frequency and the acceptance value.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Table 1 shows a four-row version. It is deliberately short. Most industrial floors fall into one of these rows, and a longer table invites rows that nobody can verify on site.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 1: a four-row table of urethane cement specifications for industrial floors<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Sistema<\/th><th>Thickness band (mm)<\/th><th>Load class<\/th><th>Chemical class<\/th><th>Design life (years)<\/th><th>Verification<\/th><\/tr><\/thead><tbody><tr><td>Trowel mortar, light duty<\/td><td>4-6<\/td><td>L2<\/td><td>C1<\/td><td>10-15<\/td><td>Wet film and core thickness, pull-off bond<\/td><\/tr><tr><td>Trowel mortar, standard<\/td><td>6-9<\/td><td>L3<\/td><td>C2<\/td><td>15-20<\/td><td>Core thickness, pull-off bond, Shore D<\/td><\/tr><tr><td>Reinforced heavy duty<\/td><td>9-12<\/td><td>L4<\/td><td>C3<\/td><td>20 and above<\/td><td>Core thickness, pull-off, impact and thermal shock<\/td><\/tr><tr><td>Cove and detail mortar<\/td><td>6-9<\/td><td>Detail only<\/td><td>C2<\/td><td>15-20<\/td><td>Visual continuity, bond at the junction<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">L1 traffic is met by the light-duty row at the lower end of its thickness band; the table does not carry a separate row for it.<\/p>\n\n\n\n<h2 id=\"why-section-thickness-drives-every-other-column\" class=\"wp-block-heading\">Why section thickness drives every other column<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Thickness is the column that constrains the rest. A 4 mm mortar and a 10 mm mortar can share a similar resin chemistry and still behave quite differently under the same pallet truck.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Point load spreads through the section at roughly 45 degrees, so a thicker section spreads the same wheel load over a wider area at the slab.<\/li>\n\n\n\n<li>Flexure, not compression, decides whether the floor cracks. Urethane cement carries high <a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-strength.html\/\" target=\"_blank\" rel=\"noopener\">compressive stress<\/a> and comparatively low tensile stress.<\/li>\n\n\n\n<li>Thermal shock travels faster through a thin section. A 4 mm floor over a cold slab reacts more sharply to a hot washdown than a 9 mm floor does.<\/li>\n\n\n\n<li>Abrasion removes a fixed depth per year in a given traffic lane. The thickness band is what converts that rate into a service period.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">There is a practical floor to the range as well. Below about 4 mm the trowel marks and the aggregate broadcast begin to interfere with each other, and the finish becomes uneven. Above about 12 mm the material cost and the exotherm during cure start to create their own problems, so thickness alone stops being a cheap way to buy capacity.<\/p>\n\n\n\n<h2 id=\"how-to-read-a-traffic-class-without-over-specifying\" class=\"wp-block-heading\">How to read a traffic class without over-specifying<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Over-specifying is the more expensive mistake in most tenders, because it is invisible. A warehouse that buys an L4 floor for a route walked by order pickers pays for material that never earns its keep and still has to maintain the same joints.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 2 sets out a simple ladder. The point loads are indicative and should be confirmed against the racking layout and the actual wheel type.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 2: load classes and the traffic each one covers<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Class<\/th><th>Typical traffic<\/th><th>Point load (kN)<\/th><th>Minimum thickness (mm)<\/th><\/tr><\/thead><tbody><tr><td>L1<\/td><td>Foot traffic, hand trolleys, light storage<\/td><td>Up to 1.5<\/td><td>4<\/td><\/tr><tr><td>L2<\/td><td>Electric pallet trucks, small containers<\/td><td>1.5 to 3<\/td><td>4-6<\/td><\/tr><tr><td>L3<\/td><td>Forklifts under 3 t, drum storage, production traffic<\/td><td>3 to 6<\/td><td>6-9<\/td><\/tr><tr><td>L4<\/td><td>Heavy forklifts, racking legs, steel-wheeled carts<\/td><td>Above 6<\/td><td>9-12<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Two details change the class in practice. The first is wheel material: a nylon wheel concentrates load into a small contact patch and is harsher than a pneumatic tire of the same axle weight. The second is the slab underneath. A urethane cement floor transfers nearly all of its load to the substrate, so a weak or hollow slab cannot be rescued by a heavier topping.<\/p>\n\n\n\n<h2 id=\"matching-the-class-to-the-spill-not-the-brochure\" class=\"wp-block-heading\">Matching the class to the spill, not the brochure<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A chemical class is only meaningful with three numbers attached: concentration, temperature and contact time. Without them, &#8220;chemical resistant&#8221; is a claim rather than a specification.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Our reference classes read as follows:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>C1.<\/strong> Occasional spillage of dilute process chemicals, sugars and cleaning agents at ambient temperature, cleaned within a shift.<\/li>\n\n\n\n<li><strong>C2.<\/strong> Regular spillage of organic acids, lactic and acetic solutions up to about 10 percent, and caustic solutions at moderate temperature, with washdown at the end of production.<\/li>\n\n\n\n<li><strong>C3.<\/strong> Concentrated process streams and hot caustic up to about 80 degrees Celsius in defined areas, with a defined spill procedure and a defined response time.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">What sits outside all three classes is worth stating plainly. Strong mineral acids at strength, chlorinated solvents in prolonged contact and direct live steam are not urethane cement duties in a standard build. They need a different system, and a table that implies otherwise will fail in the first year of service. The full boundary is set out in the chemical resistance data for the system.<\/p>\n\n\n\n<h2 id=\"system-selection-in-four-questions\" class=\"wp-block-heading\">System selection in four questions<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">System selection reduces to four questions, and the answers point to one row of Table 1.<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li><strong>What is the substrate?<\/strong> Sound concrete is the normal case. Asphalt, steel deck and existing coatings each change the answer or rule the material out.<\/li>\n\n\n\n<li><strong>What is the wettest day?<\/strong> Continuous washdown, steam cleaning and standing water push toward a heavier section and a different cove detail.<\/li>\n\n\n\n<li><strong>What is the hottest contact?<\/strong> Hot liquids, hot washdown water and oven spillage set the thermal requirement more than ambient temperature does.<\/li>\n\n\n\n<li><strong>What is the shortest shutdown?<\/strong> A 12-hour window and a two-week window rarely produce the same urethane cement specifications, even for the same room.<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">System selection done this way takes about twenty minutes on a site walk. Done from a catalog it takes five, and it usually produces a floor that is either too thin for the traffic or too heavy for the budget.<\/p>\n\n\n\n<h2 id=\"clause-wording-that-survives-a-tender-review\" class=\"wp-block-heading\">Clause wording that survives a tender review<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Most disputes about resin floors trace back to one sentence that could be read two ways. Clause wording is therefore part of the urethane cement specifications, not decoration added at the end.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Compare these two lines:<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Weak: &#8220;Urethane cement floor, 6 mm, chemical resistant, installed to manufacturer instructions.&#8221;<\/li>\n\n\n\n<li>Workable: &#8220;Trowel-applied urethane cement mortar, 6 mm plus or minus 0.5 mm measured by core sample at a rate of one per 200 square meters, class C2 exposure as defined in the schedule, coving 100 mm high with a 25 mm radius for dry industrial areas; wet or hygienic areas take a larger radius specified by the project.&#8221;<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">The second line names the method, the tolerance, the measurement and the exposure class. It also gives the contractor a fair target, which matters: a clause that cannot be measured invites a price for something that cannot be delivered.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Good clause wording also settles who supplies what. Primer, broadcast aggregate, seal coat and coving are separate cost lines in some contracts and bundled in others. Naming them in the clause removes the ambiguity before the quote arrives.<\/p>\n\n\n\n<h2 id=\"what-the-verification-test-column-must-name\" class=\"wp-block-heading\">What the verification test column must name<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The last column is the one most often left vague, and it is the one that protects the buyer. A verification test needs a method, a frequency and an acceptance value, or it is only a gesture.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 3 lists the tests we would expect to see in a project of any size.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 3: verification tests, frequencies and acceptance values<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th>Test<\/th><th>Frequency<\/th><th>Acceptance<\/th><th>What it catches<\/th><\/tr><\/thead><tbody><tr><td>Wet film thickness<\/td><td>Each day of laying<\/td><td>Within 10 percent of the specified wet build<\/td><td>Thin application before it cures<\/td><\/tr><tr><td>Core sample thickness<\/td><td>One per 200 square meters, minimum three<\/td><td>Within the stated range<\/td><td>System applied thinner than quoted<\/td><\/tr><tr><td>Pull-off bond<\/td><td>One per 500 square meters<\/td><td>Substrate failure in the concrete, or the stated bond value; a lower reading is a fail<\/td><td>Poor preparation, laitance, contamination<\/td><\/tr><tr><td>Shore D hardness<\/td><td>One set per pour<\/td><td>Within the supplier&#8217;s declared range<\/td><td>Wrong mix ratio, incomplete cure<\/td><\/tr><tr><td>Visual and cove continuity<\/td><td>Whole area<\/td><td>No pinholes, no gaps at the junction<\/td><td>Hygiene failures at the wall base<\/td><\/tr><\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cores-upright.jpg\" alt=\"Three cores cut from a sealed floor standing upright with the cut faces toward camera\" class=\"wp-image-10680\" srcset=\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cores-upright.jpg 800w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cores-upright-300x225.jpg 300w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cores-upright-768x576.jpg 768w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cores-upright-16x12.jpg 16w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cores-upright-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Figure 1: three cores standing upright with the cut faces turned to the camera.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A verification test written without an acceptance value gets recorded and then ignored. Writing &#8220;pull-off test to be carried out&#8221; leaves the contractor free to report 0.4 MPa as a pass. Naming the figure in advance is what makes the column useful.<\/p>\n\n\n\n<h2 id=\"where-the-service-life-figure-comes-from\" class=\"wp-block-heading\">Where the service life figure comes from<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Service life is a forecast, not a warranty, and the difference matters when a tender compares two suppliers. A stated service life should be traceable to four inputs: thickness, traffic, cleaning regime and chemical exposure.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li>Thickness sets how much material abrasion can remove before the system is compromised.<\/li>\n\n\n\n<li>Traffic sets the rate of that removal in the main lanes.<\/li>\n\n\n\n<li>Cleaning sets both abrasion and thermal cycling, and steam cleaning shortens life faster than most buyers expect.<\/li>\n\n\n\n<li>Chemical exposure sets the rate of surface change in the areas where spills collect.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">When any one of those inputs is unknown, the honest answer is a range. A supplier who quotes a single number for service life across all areas of a plant is either assuming a cleaning regime or guessing. Ask which one.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Service life also has a maintenance component. A floor that is cleaned, inspected and spot-repaired at year seven will reach the upper end of its range. The same floor with no inspection tends to fail at a joint rather than in the field, and that failure is usually cheap to prevent and expensive to ignore.<\/p>\n\n\n\n<h2 id=\"building-the-tender-schedule-around-the-table\" class=\"wp-block-heading\">Building the tender schedule around the table<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The tender schedule is where the table meets the contract. A schedule that lists only square meters and a rate leaves the urethane cement specifications to the bidder, and bidders read documents differently.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">We would expect the schedule to carry:<\/p>\n\n\n\n<ol class=\"wp-block-list\">\n<li>Room or area reference, with the exposure class for each.<\/li>\n\n\n\n<li>The system row from Table 1, by name and not by product code alone.<\/li>\n\n\n\n<li>Section thickness, coving height and any drainage falls.<\/li>\n\n\n\n<li>The verification tests and the party responsible for paying for them.<\/li>\n\n\n\n<li>Phasing and the shutdown window for each area.<\/li>\n\n\n\n<li>The submittals required before work starts: data sheets, method statement, batch records.<\/li>\n<\/ol>\n\n\n\n<p class=\"wp-block-paragraph\">A tender schedule built this way also makes bid comparison honest. Two prices for the same row can be compared. Two prices for &#8220;epoxy or similar&#8221; cannot, because they are not prices for the same floor.<\/p>\n\n\n\n<h2 id=\"six-errors-when-a-table-is-copied-between-projects\" class=\"wp-block-heading\">Six errors when a table is copied between projects<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">The six errors below are what happens when the clause is copied without the row it came from.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Specification tables travel. A consultant reuses one from a dairy on a chemical plant, or a contractor reuses one from a warehouse on a kitchen, and the errors are predictable.<\/p>\n\n\n\n<ul class=\"wp-block-list\">\n<li><strong>Chemical class carried over without the concentration.<\/strong> The word &#8220;acid&#8221; survives the copy; the percentage does not.<\/li>\n\n\n\n<li><strong>Section thickness reduced to save cost.<\/strong> A 9 mm row becomes 6 mm and the class is left unchanged.<\/li>\n\n\n\n<li><strong>Verification column deleted.<\/strong> The tests disappear because the previous client did not enforce them.<\/li>\n\n\n\n<li><strong>Cove height left at the old value.<\/strong> 100 mm is common; some hygiene standards expect 150 mm.<\/li>\n\n\n\n<li><strong>Design life inherited.<\/strong> A 20-year figure moves to a room with steam cleaning and no inspection.<\/li>\n\n\n\n<li><strong>Product names kept, chemistry changed.<\/strong> The named product is no longer the one being supplied.<\/li>\n<\/ul>\n\n\n\n<p class=\"wp-block-paragraph\">Each of these is fixable in a ten-minute review. What is not fixable is the habit of treating a table as boilerplate.<\/p>\n\n\n\n<h2 id=\"how-kaida-paint-supports-specification-work\" class=\"wp-block-heading\">How Kaida Paint supports specification work<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Kaida Paint supplies urethane cement systems and the documentation that sits behind them: data sheets with declared values, method statements with hold points, batch records and core-sample logs. Our technical desk will read a tender schedule and mark the rows that cannot be met at the stated thickness or exposure.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For projects where the exposure is unclear, we cast a sample panel from the production batch and test it against the actual process chemical before the urethane cement specifications are fixed. The same panel is kept with the project record. It answers a color question in year five, and a bond question is answered from the record rather than from memory.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If you have a schedule with a table of urethane cement specifications already attached, send it with the room list and the cleaning regime. We will return the annotated table and a build-up per area, at no cost and without a sales visit.<\/p>\n\n\n\n<h2 id=\"frequently-asked-questions\" class=\"wp-block-heading\">Domande frequenti<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"is-a-urethane-cement-specification-the-same-as-a-data-sheet\">Is a urethane cement specification the same as a data sheet?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. A <a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-data-sheet.html\/\" target=\"_blank\" rel=\"noopener\">data sheet<\/a> describes one product. A specification states what the floor must achieve in a given room and how that will be verified. The data sheet supports the specification; it does not replace it.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-thickness-should-the-table-start-at\">What thickness should the table start at?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Four millimeters is the practical minimum for a trowel-applied system in light duty. Below that, the finish becomes uneven and the thickness tolerance is hard to hold.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"can-one-table-cover-a-whole-factory\">Can one table cover a whole factory?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Only if the factory has one exposure. Most have at least three: dry storage, wet process and a chemical area. Separate rows for each are simpler than one row with exceptions.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"who-pays-for-the-verification-tests\">Who pays for the verification tests?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">That is a commercial decision, but it should be written into the schedule. Splitting the cost is common: the contractor pays for the routine tests and the client pays for any independent cores.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"how-do-i-check-a-contractor-s-own-table\">How do I check a contractor&#8217;s own table?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Ask for the project it came from, the exposure class used there, and the core-sample results. A table that cannot be traced to a completed job is a template.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"does-a-higher-load-class-always-last-longer\">Does a higher load class always last longer?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. A heavier section in a light-duty area adds cost without adding life, and it can add joint problems. The right class is the one that matches the traffic.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-shortens-design-life-most\">What shortens design life most?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Steam cleaning and unaddressed joint movement, in that order, in our experience. Both are visible early if anyone inspects the floor.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\"><\/p>","protected":false},"excerpt":{"rendered":"<p>A workable set of urethane cement specifications fits on one page. Each row pairs a [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":10679,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"om_disable_all_campaigns":false,"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_uf_show_specific_survey":0,"_uf_disable_surveys":false,"footnotes":""},"categories":[1],"tags":[2584,2583,2582,2581,2537],"class_list":["post-10696","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-faq","tag-chemical-resistant-flooring-specification","tag-resin-floor-load-class","tag-urethane-cement-specification-table","tag-urethane-cement-specifications","tag-urethane-cement-thickness"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v26.2 (Yoast SEO v26.5) - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>Urethane Cement Specifications: System, Load and Chemistry<\/title>\n<meta name=\"description\" content=\"A working urethane cement specifications table, column by column: system, thickness band, load class, chemical class, design life and verification test.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-specification-table.html\/\" \/>\n<meta property=\"og:locale\" content=\"it_IT\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Urethane Cement Specifications: System, Load and Chemistry\" \/>\n<meta property=\"og:description\" content=\"A working urethane cement specifications table, column by column: system, thickness band, load class, chemical class, design life and verification test.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-specification-table.html\/\" \/>\n<meta property=\"og:site_name\" content=\"KAIDA PAINT\u00ae\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-20T06:30:13+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-20T06:30:15+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"jinyupaint\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Scritto da\" \/>\n\t<meta name=\"twitter:data1\" content=\"jinyupaint\" \/>\n\t<meta name=\"twitter:label2\" content=\"Tempo di lettura stimato\" \/>\n\t<meta name=\"twitter:data2\" content=\"12 minuti\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html\",\"url\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html\",\"name\":\"Urethane Cement Specifications: System, Load and Chemistry\",\"isPartOf\":{\"@id\":\"https:\/\/www.jinyupaint.com\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#primaryimage\"},\"image\":{\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg\",\"datePublished\":\"2026-11-20T06:30:13+00:00\",\"dateModified\":\"2026-11-20T06:30:15+00:00\",\"author\":{\"@id\":\"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b\"},\"description\":\"A working urethane cement specifications table, column by column: system, thickness band, load class, chemical class, design life and verification test.\",\"breadcrumb\":{\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#breadcrumb\"},\"inLanguage\":\"it-IT\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"it-IT\",\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#primaryimage\",\"url\":\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg\",\"contentUrl\":\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg\",\"width\":800,\"height\":600,\"caption\":\"Cut section of a cured urethane cement sample showing seal, body coat and primer over slab\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/www.jinyupaint.com\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Urethane Cement Specifications: System, Load and Chemistry\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.jinyupaint.com\/#website\",\"url\":\"https:\/\/www.jinyupaint.com\/\",\"name\":\"KAIDA PAINT\u00ae\",\"description\":\"Industrial Coatings Manufacturer &amp; Global Flooring Solutions Contractor\",\"alternateName\":\"JINYU PAINT\u00ae\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.jinyupaint.com\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"it-IT\"},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b\",\"name\":\"jinyupaint\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"it-IT\",\"@id\":\"https:\/\/www.jinyupaint.com\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842\",\"contentUrl\":\"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842\",\"caption\":\"jinyupaint\"},\"sameAs\":[\"https:\/\/www.jinyupaint.com\"],\"url\":\"https:\/\/www.jinyupaint.com\/it\/author\/jinyupaint\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Urethane Cement Specifications: System, Load and Chemistry","description":"A working urethane cement specifications table, column by column: system, thickness band, load class, chemical class, design life and verification test.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.jinyupaint.com\/it\/urethane-cement-specification-table.html\/","og_locale":"it_IT","og_type":"article","og_title":"Urethane Cement Specifications: System, Load and Chemistry","og_description":"A working urethane cement specifications table, column by column: system, thickness band, load class, chemical class, design life and verification test.","og_url":"https:\/\/www.jinyupaint.com\/it\/urethane-cement-specification-table.html\/","og_site_name":"KAIDA PAINT\u00ae","article_published_time":"2026-11-20T06:30:13+00:00","article_modified_time":"2026-11-20T06:30:15+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg","type":"image\/jpeg"}],"author":"jinyupaint","twitter_card":"summary_large_image","twitter_misc":{"Scritto da":"jinyupaint","Tempo di lettura stimato":"12 minuti"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"WebPage","@id":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html","url":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html","name":"Urethane Cement Specifications: System, Load and Chemistry","isPartOf":{"@id":"https:\/\/www.jinyupaint.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#primaryimage"},"image":{"@id":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#primaryimage"},"thumbnailUrl":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg","datePublished":"2026-11-20T06:30:13+00:00","dateModified":"2026-11-20T06:30:15+00:00","author":{"@id":"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b"},"description":"A working urethane cement specifications table, column by column: system, thickness band, load class, chemical class, design life and verification test.","breadcrumb":{"@id":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#breadcrumb"},"inLanguage":"it-IT","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html"]}]},{"@type":"ImageObject","inLanguage":"it-IT","@id":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#primaryimage","url":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg","contentUrl":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cured-section-cut-sample.jpg","width":800,"height":600,"caption":"Cut section of a cured urethane cement sample showing seal, body coat and primer over slab"},{"@type":"BreadcrumbList","@id":"https:\/\/www.jinyupaint.com\/urethane-cement-specification-table.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.jinyupaint.com\/"},{"@type":"ListItem","position":2,"name":"Urethane Cement Specifications: System, Load and Chemistry"}]},{"@type":"WebSite","@id":"https:\/\/www.jinyupaint.com\/#website","url":"https:\/\/www.jinyupaint.com\/","name":"KAIDA PAINT\u00ae","description":"Produttore di rivestimenti industriali e fornitore globale di soluzioni per pavimentazioni","alternateName":"JINYU PAINT\u00ae","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.jinyupaint.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"it-IT"},{"@type":"Person","@id":"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b","name":"jinyupaint","image":{"@type":"ImageObject","inLanguage":"it-IT","@id":"https:\/\/www.jinyupaint.com\/#\/schema\/person\/image\/","url":"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842","contentUrl":"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842","caption":"jinyupaint"},"sameAs":["https:\/\/www.jinyupaint.com"],"url":"https:\/\/www.jinyupaint.com\/it\/author\/jinyupaint"}]}},"_links":{"self":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts\/10696","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/comments?post=10696"}],"version-history":[{"count":3,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts\/10696\/revisions"}],"predecessor-version":[{"id":10714,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts\/10696\/revisions\/10714"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/media\/10679"}],"wp:attachment":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/media?parent=10696"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/categories?post=10696"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/tags?post=10696"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}