{"id":10624,"date":"2026-11-20T04:33:24","date_gmt":"2026-11-20T04:33:24","guid":{"rendered":"https:\/\/www.jinyupaint.com\/?p=10624"},"modified":"2026-11-20T04:33:25","modified_gmt":"2026-11-20T04:33:25","slug":"urethane-cement-strength","status":"publish","type":"post","link":"https:\/\/www.jinyupaint.com\/it\/urethane-cement-strength.html","title":{"rendered":"Urethane Cement Strength: Reading Compressive Data"},"content":{"rendered":"<p class=\"wp-block-paragraph\">Urethane cement strength is usually quoted as one figure in newtons per square millimeter, and that single figure is the least useful number on the data sheet.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Four properties decide how a urethane cement floor performs: resistance to load, resistance to bending, stiffness and adhesion. Each maps onto a failure the buyer is trying to avoid, which is cracking, rutting or lifting, and no single number describes all four. That gap is the whole difficulty with a single-figure data sheet.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">This article explains what each figure measures, how the conditions behind it change the answer, and how to compare two products without being misled by a headline.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"the-short-answer\">The short answer<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Compressive strength tells you how much load the material carries in pure compression, which is rare in a floor.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Flexural strength tells you how it resists bending over a void or a moving joint, which is common.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Tensile strength tells you how it behaves when pulled, which is usually measured indirectly and usually low.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Modulus tells you how stiff it is, and stiffness is what decides whether a floor cracks rather than flexes.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A useful sheet gives all four, with the conditions attached. The table below is the whole comparison, and the rest of this article explains each column.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 1: The four numbers, what each predicts, and the range industrial products commonly report.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Propriet\u00e0<\/th><th scope=\"col\">Predicts<\/th><th scope=\"col\">Commonly reported<\/th><\/tr><\/thead>\n<tbody>\n<tr><td>Compression<\/td><td>Load capacity, batch quality<\/td><td>C30-C50 on a cube<\/td><\/tr>\n<tr><td>Flexure<\/td><td>Crack resistance over voids<\/td><td>A declared value in N\/mm2<\/td><\/tr>\n<tr><td>Tension<\/td><td>Behavior at restrained edges<\/td><td>2-5 N\/mm2 by splitting<\/td><\/tr>\n<tr><td>Modulus<\/td><td>Stiffness, movement transfer<\/td><td>10-25 GPa<\/td><\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">A sheet that gives one is a summary written for a brochure rather than a document written for a specification.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A specification that names only the first of those four has described a material and not a floor.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"what-the-compressive-figure-actually-measures\">What the compressive figure actually measures<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A cube or a cylinder is loaded until it fails, and the peak load is divided by the area. The result is a class, such as C35, meaning 35 newtons per square millimeter.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That figure is useful for comparing products and for checking that a batch has not been under-filled with cement.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A compressive strength figure is much less useful for predicting a floor. A urethane cement floor rarely fails in pure compression, because the slab beneath it is carrying the load and spreading it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">What the figure answers is whether this batch was under-filled with cement. It cannot answer whether this floor will fail, and it is printed on every sheet because it is cheap and reproducible rather than because it is decisive. The <a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-data-sheet.html\/\" target=\"_blank\" rel=\"noopener\">data sheet fields<\/a> that do describe failure are the ones worth reading first.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where compression does matter is under a point load on a thin build, and under a machine foot where the material is confined by a steel plate.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"why-flexural-strength-matters-more\">Why flexural strength matters more<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A floor bends. It bends over a void under a slab, over a joint that opens, and over any discontinuity that has not been properly supported.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A floor bends before it crushes, which is why a flexural strength figure belongs beside compression on every sheet, and why a supplier who quotes only compression is telling you which test they ran rather than which property matters.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A flexural figure also converts into a decision, which is the part most specifiers never make. At the same load and the same support conditions, a higher flexural value buys a wider joint spacing or a thinner build, and a lower one demands the opposite. Read it as a trade between the number of joints you will maintain and the millimeters you will pay for, rather than as a ranking. The actual conversion depends on the slab, the substrate and the load, so it belongs to the designer&#8217;s calculation and not to a brochure.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That trade is why two products with the same compressive class can need different joint layouts on the same floor. A tender that fixes the joint spacing before the flexural class is read has fixed the wrong thing first.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The bending resistance of the material decides whether it cracks at that point or carries the load across it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Flexural class is the figure a flooring engineer reads first, and why a high compressive class with a low flexural class describes a brittle floor.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Toughness is the property a client actually wants in a washdown room, and it is not the same as being strong. A tough floor absorbs an impact; a strong one resists a load and may shatter under a dropped tool.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The ratio between the two is a rough measure of toughness. A material with high compression and low bending will crack before it crushes.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For a washdown room with thermal movement, the bending figure is the one that decides whether the surface survives its first winter.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Those ranges describe specimens from the same batch, tested to the same method at the same age, and the <a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-definition.html\/\" target=\"_blank\" rel=\"noopener\">definition and chemistry<\/a> of the binder is what makes the numbers move with the mix. A supplier that quotes a flexural class code without the test method, the specimen dimensions and the age has given a label rather than a number, and the label cannot be used for comparison.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"tensile-strength-and-how-it-is-measured\">Tensile strength and how it is measured<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Direct tension is difficult to test on a brittle material, so most figures come from a splitting test or are derived from the bending result.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The splitting test loads a cylinder across its diameter, and the failure load is converted into a tensile value.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That value is typically a tenth of the compressive figure, which is why tensile cracking is the normal failure mode in a restrained floor.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where a floor is restrained by walls, curbs or a stiff substrate, the tensile stress builds until it exceeds the strength, and a crack appears.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">For a plant manager the practical summary is simple: the number that predicts a crack is bending, and the number that predicts a rut is compression. Most floor failures in wet rooms are cracks.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The practical consequence is joints. The same logic applies at every restraint: a column, a curb, a drain surround. Each one is a place where the floor cannot move, so each one needs either a joint or a detail that absorbs the movement.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A joint is cheaper than the tensile strength required to avoid one, and it is also far easier to inspect in service.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"modulus-and-why-a-stiff-floor-cracks\">Modulus, and why a stiff floor cracks<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Modulus measures how much the material deforms under a given stress. A high stiffness means stiff, and a low stiffness means compliant.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A stiff topping on a moving slab transfers the movement into itself, and a compliant one absorbs it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The resin phase is why a urethane cement floor at 6 mm can survive movement that would crack a rigid cementitious topping of the same thickness.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The stiffness figure is rarely quoted on a data sheet, and its absence is a useful signal about how the sheet was produced.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where it is quoted, compare it with the substrate rather than with another product. Where a slab is stiff and the floor is stiff, every movement becomes a stress in the floor. Where the floor is slightly more compliant, the same movement becomes a small deflection and no crack.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">The mismatch between floor and slab is what generates stress.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"test-age-curing-regime-and-the-gap-to-site\">Test age, curing regime and the gap to site<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Concrete is tested at 28 days by convention, and many urethane cement sheets quote the same age for comparability.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">But a resin-modified material develops most of its strength early: seven days usually reaches 75 to 90 per cent of the 28-day figure, and the remaining gap depends on the formulation and the curing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That is not a reason to quote the seven-day number without saying so. A 28-day figure and a 7-day figure are different claims.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Ask which age produced the figure, and ask whether the sample was wet-cured, dry-cured or sealed.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A curing regime that keeps water in the sample will produce a higher figure than one that lets it dry, and both are legitimate as long as they are stated.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 2: What changes the number.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Variable<\/th><th scope=\"col\">Effetto<\/th><\/tr><\/thead>\n<tbody>\n<tr><td>Test age 7 vs 28 days<\/td><td>28-day figure typically 10-25% higher, depending on formulation<\/td><\/tr>\n<tr><td>Wet vs dry cure<\/td><td>Higher when water retained<\/td><\/tr>\n<tr><td>Cube vs cylinder<\/td><td>Cylinder reads lower<\/td><\/tr>\n<tr><td>Specimen size<\/td><td>Larger specimens read lower<\/td><\/tr>\n<tr><td>Loading rate<\/td><td>Faster loading reads higher<\/td><\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"specimen-size-and-the-scale-effect\">Specimen size and the scale effect<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A small specimen reads higher than a large one, because a small volume is less likely to contain the largest flaw.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Standards fix the size and the shape for that reason, and why a figure quoted from a 40 mm cube cannot be compared with one from a 150 mm cube.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Specimen size also affects the failure mode. A slender prism bends, and a squat cube crushes, and the two numbers describe different behavior.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where a supplier quotes a very high figure, the first question is the specimen dimensions and the second is the age at testing.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">If either is missing, the figure is a number without a context, and a number without a context is not evidence.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Age at testing also explains most of the variation between two suppliers who claim the same product chemistry. One reports at seven days, the other at twenty-eight, and the numbers differ by a fifth.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"the-declared-class-and-what-it-commits-to\">The declared class and what it commits to<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">A laboratory sample is cast in a mold, compacted carefully and cured in controlled conditions. A site sample is placed by trowel, compacted by hand and cured in a room that may be at 5 \u00b0C. The gap between the two is the reason a declared class should be read as a material property rather than a prediction of the floor, and it is where a class is most often misread.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That is not a criticism of the material. It is a description of what a type test can and cannot do. Where a client needs evidence about the installed floor, the test is a core sample and a pull-off, not a cube in a laboratory. A tender that compares two urethane cement products on a single figure is only valid if four conditions match, and they usually do not.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">A declared class is a statement made under a standard, and it carries legal weight in a way that a brochure figure does not.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It commits the manufacturer to a value produced by a defined test, and it allows a specifier to compare products on a common basis.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">It does not commit the installer to placing the material correctly, and it does not commit the floor to reaching that value in service.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Read the declared class as the start of the conversation rather than the end of it.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Keep the test reports with it rather than only the summary, because a summary cannot be checked and a report can.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">That file is also what a second contractor reads before quoting a repair. A floor with a documented build and a set of core results is easier to repair than one with a brochure and no records.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Where a project requires evidence, the declaration and the site test belong together in the handover file.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"comparing-and-specifying-on-the-same-four-conditions\">Comparing and specifying on the same four conditions<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Reading a sheet and writing a clause rest on the same four conditions: the property, the age at testing, the specimen dimensions and the curing regime. A comparison that ignores one of them is not a comparison, and a clause that omits one is not checkable.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Compare like with like first. Where one sheet quotes a 28-day cube and the other a 7-day cylinder, the two numbers are not comparable, and the higher one is not necessarily stronger.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Compare the ratio of flexural to compressive class as well, because that ratio describes toughness rather than strength. A comparison must also match the dimensions of the test piece, the method and the age, or the numbers describe two different tests., because stiffness decides how the floor behaves over a joint. Finally, ask what the product does at the temperature and thickness you are specifying, because a figure at 20 \u00b0C says nothing about a freezer.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Writing the clause is the same list in the other direction. Name the property, the class, the age at testing and the standard, and state the flexural class as well as the compressive one, because the second alone describes a brittle material. State the site tests separately: thickness by core, adhesion by pull-off. Those describe the floor rather than the drum.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Require the declared class document where a project needs one, and keep it with the handover file. A specification written that way makes a tender comparable, because two bidders working from the same four items will produce prices that describe the same floor, and it leaves <a href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-thickness.html\/\" target=\"_blank\" rel=\"noopener\">thickness selection<\/a> to a separate clause, where it belongs.<\/p>\n\n\n\n<p class=\"wp-block-paragraph\">Table 3: What to require, and when.<\/p>\n\n\n\n<figure class=\"wp-block-table\"><table><thead><tr><th scope=\"col\">Articolo<\/th><th scope=\"col\">Require<\/th><th scope=\"col\">Evidence<\/th><\/tr><\/thead>\n<tbody>\n<tr><td>Compressive class<\/td><td>Class plus age at testing<\/td><td>Test report<\/td><\/tr>\n<tr><td>Flexural class<\/td><td>Class plus specimen dimensions<\/td><td>Test report<\/td><\/tr>\n<tr><td>Tensile or splitting<\/td><td>Method and value<\/td><td>Test report<\/td><\/tr>\n<tr><td>Modulus<\/td><td>Value if available<\/td><td>Test report<\/td><\/tr>\n<tr><td>Installed floor<\/td><td>Core and pull-off<\/td><td>Site record<\/td><\/tr>\n<\/tbody><\/table><\/figure>\n\n\n\n<figure class=\"wp-block-image size-full\"><img fetchpriority=\"high\" decoding=\"async\" width=\"800\" height=\"600\" src=\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-test-machine-compression.jpg\" alt=\"Compression test machine loading a urethane cement cube with the failure pattern visible\" class=\"wp-image-10604\" srcset=\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-test-machine-compression.jpg 800w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-test-machine-compression-300x225.jpg 300w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-test-machine-compression-768x576.jpg 768w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-test-machine-compression-16x12.jpg 16w, https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-test-machine-compression-600x450.jpg 600w\" sizes=\"(max-width: 800px) 100vw, 800px\" \/><\/figure>\n\n\n\n<p class=\"wp-block-paragraph\">Figure 1: the failure pattern matters as much as the peak load.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"frequently-asked-questions\">Domande frequenti<\/h2>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-compressive-strength-does-urethane-cement-have\">What compressive strength does urethane cement have?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Most industrial products report between C30 and C50 on a cube at a stated age, which is 30 to 50 newtons per square millimeter. That range is a market observation rather than a grade, and two products inside it are only comparable when the standard, the specimen and the age match.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"is-higher-compressive-strength-better\">Is higher compressive strength better?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Not automatically. A higher figure often comes with a higher stiffness, and a stiffer floor cracks more readily over a moving joint.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"why-is-flexural-strength-more-important\">Why is flexural strength more important?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Because floors bend over voids and joints rather than being crushed, and bending resistance decides whether a crack forms.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-is-a-typical-tensile-strength\">What is a typical tensile strength?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Around a tenth of the compressive value, which is why restrained floors crack unless joints are provided.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"why-do-two-data-sheets-quote-different-figures-for-similar-products\">Why do two data sheets quote different figures for similar products?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">Usually because the test age, specimen size or curing regime differ. Compare those before comparing the numbers.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"does-strength-predict-chemical-resistance\">Does strength predict chemical resistance?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">No. Chemical resistance comes from the resin phase and is reported in a separate table with concentrations and temperatures.<\/p>\n\n\n\n<h3 class=\"wp-block-heading\" id=\"what-test-proves-the-installed-floor\">What test proves the installed floor?<\/h3>\n\n\n\n<p class=\"wp-block-paragraph\">A core sample for thickness and a pull-off test for adhesion. Neither is a strength test, and both describe the floor rather than the material.<\/p>\n\n\n\n<h2 class=\"wp-block-heading\" id=\"working-with-kaida-paint\">Working with Kaida Paint<\/h2>\n\n\n\n<p class=\"wp-block-paragraph\">Kaida Paint reports urethane cement class with the test age, the specimen size and the standard behind it, and we will send the test reports on request. Send the loads and the room conditions, and we will say which of the four properties decides your specification.<\/p>","protected":false},"excerpt":{"rendered":"<p>Urethane cement strength is usually quoted as one figure in newtons per square millimeter, and [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":10603,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"om_disable_all_campaigns":false,"_monsterinsights_skip_tracking":false,"_monsterinsights_sitenote_active":false,"_monsterinsights_sitenote_note":"","_monsterinsights_sitenote_category":0,"_uf_show_specific_survey":0,"_uf_disable_surveys":false,"footnotes":""},"categories":[1],"tags":[2517,2515,2518,2516,2514],"class_list":["post-10624","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-faq","tag-age-at-testing","tag-cementitious-urethane-compressive-class","tag-declared-performance","tag-flexural-class","tag-urethane-cement-strength"],"yoast_head":"<!-- This site is optimized with the Yoast SEO Premium plugin v26.2 (Yoast SEO v26.5) - https:\/\/yoast.com\/wordpress\/plugins\/seo\/ -->\n<title>Urethane Cement Strength: Reading Compressive Data<\/title>\n<meta name=\"description\" content=\"What compressive, tensile and flexural figures predict on a urethane cement floor in service, why the test age matters, and how to compare two products.\" \/>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-strength.html\/\" \/>\n<meta property=\"og:locale\" content=\"it_IT\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Urethane Cement Strength: Reading Compressive Data\" \/>\n<meta property=\"og:description\" content=\"What compressive, tensile and flexural figures predict on a urethane cement floor in service, why the test age matters, and how to compare two products.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.jinyupaint.com\/it\/urethane-cement-strength.html\/\" \/>\n<meta property=\"og:site_name\" content=\"KAIDA PAINT\u00ae\" \/>\n<meta property=\"article:published_time\" content=\"2026-11-20T04:33:24+00:00\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-20T04:33:25+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"800\" \/>\n\t<meta property=\"og:image:height\" content=\"600\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"author\" content=\"jinyupaint\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Scritto da\" \/>\n\t<meta name=\"twitter:data1\" content=\"jinyupaint\" \/>\n\t<meta name=\"twitter:label2\" content=\"Tempo di lettura stimato\" \/>\n\t<meta name=\"twitter:data2\" content=\"12 minuti\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\/\/schema.org\",\"@graph\":[{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html\",\"url\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html\",\"name\":\"Urethane Cement Strength: Reading Compressive Data\",\"isPartOf\":{\"@id\":\"https:\/\/www.jinyupaint.com\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#primaryimage\"},\"image\":{\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#primaryimage\"},\"thumbnailUrl\":\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg\",\"datePublished\":\"2026-11-20T04:33:24+00:00\",\"dateModified\":\"2026-11-20T04:33:25+00:00\",\"author\":{\"@id\":\"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b\"},\"description\":\"What compressive, tensile and flexural figures predict on a urethane cement floor in service, why the test age matters, and how to compare two products.\",\"breadcrumb\":{\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#breadcrumb\"},\"inLanguage\":\"it-IT\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"it-IT\",\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#primaryimage\",\"url\":\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg\",\"contentUrl\":\"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg\",\"width\":800,\"height\":600,\"caption\":\"Cube and prism specimens of urethane cement on a laboratory bench before testing\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\/\/www.jinyupaint.com\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Urethane Cement Strength: Reading Compressive Data\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\/\/www.jinyupaint.com\/#website\",\"url\":\"https:\/\/www.jinyupaint.com\/\",\"name\":\"KAIDA PAINT\u00ae\",\"description\":\"Industrial Coatings Manufacturer &amp; Global Flooring Solutions Contractor\",\"alternateName\":\"JINYU PAINT\u00ae\",\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\/\/www.jinyupaint.com\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"it-IT\"},{\"@type\":\"Person\",\"@id\":\"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b\",\"name\":\"jinyupaint\",\"image\":{\"@type\":\"ImageObject\",\"inLanguage\":\"it-IT\",\"@id\":\"https:\/\/www.jinyupaint.com\/#\/schema\/person\/image\/\",\"url\":\"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842\",\"contentUrl\":\"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842\",\"caption\":\"jinyupaint\"},\"sameAs\":[\"https:\/\/www.jinyupaint.com\"],\"url\":\"https:\/\/www.jinyupaint.com\/it\/author\/jinyupaint\"}]}<\/script>\n<!-- \/ Yoast SEO Premium plugin. -->","yoast_head_json":{"title":"Urethane Cement Strength: Reading Compressive Data","description":"What compressive, tensile and flexural figures predict on a urethane cement floor in service, why the test age matters, and how to compare two products.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.jinyupaint.com\/it\/urethane-cement-strength.html\/","og_locale":"it_IT","og_type":"article","og_title":"Urethane Cement Strength: Reading Compressive Data","og_description":"What compressive, tensile and flexural figures predict on a urethane cement floor in service, why the test age matters, and how to compare two products.","og_url":"https:\/\/www.jinyupaint.com\/it\/urethane-cement-strength.html\/","og_site_name":"KAIDA PAINT\u00ae","article_published_time":"2026-11-20T04:33:24+00:00","article_modified_time":"2026-11-20T04:33:25+00:00","og_image":[{"width":800,"height":600,"url":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg","type":"image\/jpeg"}],"author":"jinyupaint","twitter_card":"summary_large_image","twitter_misc":{"Scritto da":"jinyupaint","Tempo di lettura stimato":"12 minuti"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"WebPage","@id":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html","url":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html","name":"Urethane Cement Strength: Reading Compressive Data","isPartOf":{"@id":"https:\/\/www.jinyupaint.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#primaryimage"},"image":{"@id":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#primaryimage"},"thumbnailUrl":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg","datePublished":"2026-11-20T04:33:24+00:00","dateModified":"2026-11-20T04:33:25+00:00","author":{"@id":"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b"},"description":"What compressive, tensile and flexural figures predict on a urethane cement floor in service, why the test age matters, and how to compare two products.","breadcrumb":{"@id":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#breadcrumb"},"inLanguage":"it-IT","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.jinyupaint.com\/urethane-cement-strength.html"]}]},{"@type":"ImageObject","inLanguage":"it-IT","@id":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#primaryimage","url":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg","contentUrl":"https:\/\/www.jinyupaint.com\/wp-content\/uploads\/2026\/11\/urethane-cement-cube-and-prism-specimens.jpg","width":800,"height":600,"caption":"Cube and prism specimens of urethane cement on a laboratory bench before testing"},{"@type":"BreadcrumbList","@id":"https:\/\/www.jinyupaint.com\/urethane-cement-strength.html#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.jinyupaint.com\/"},{"@type":"ListItem","position":2,"name":"Urethane Cement Strength: Reading Compressive Data"}]},{"@type":"WebSite","@id":"https:\/\/www.jinyupaint.com\/#website","url":"https:\/\/www.jinyupaint.com\/","name":"KAIDA PAINT\u00ae","description":"Produttore di rivestimenti industriali e fornitore globale di soluzioni per pavimentazioni","alternateName":"JINYU PAINT\u00ae","potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.jinyupaint.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"it-IT"},{"@type":"Person","@id":"https:\/\/www.jinyupaint.com\/#\/schema\/person\/c180feaa2102b492d985efe62f9cb01b","name":"jinyupaint","image":{"@type":"ImageObject","inLanguage":"it-IT","@id":"https:\/\/www.jinyupaint.com\/#\/schema\/person\/image\/","url":"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842","contentUrl":"https:\/\/www.jinyupaint.com\/wp-content\/litespeed\/avatar\/b702e163685e9eae5ab604489f61127a.jpg?ver=1795151842","caption":"jinyupaint"},"sameAs":["https:\/\/www.jinyupaint.com"],"url":"https:\/\/www.jinyupaint.com\/it\/author\/jinyupaint"}]}},"_links":{"self":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts\/10624","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/comments?post=10624"}],"version-history":[{"count":2,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts\/10624\/revisions"}],"predecessor-version":[{"id":10646,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/posts\/10624\/revisions\/10646"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/media\/10603"}],"wp:attachment":[{"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/media?parent=10624"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/categories?post=10624"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/www.jinyupaint.com\/it\/wp-json\/wp\/v2\/tags?post=10624"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}